Aeris, after-pot cooling

Printable Version

Aeris®, after-pot cooling

For galvanizing processes, the cooling tower design remains a major issue for product quality. The high capacity requirements have resulted in increased blowing velocities and higher cooling towers, both of which have a detrimental effect on cooling control due to concern over strip stabilization. Strip fluttering causes both additional zinc consumption and reduced coating quality, both of which can be costly.

Aeris®, Fives' proprietary after-pot cooling technology, is an efficient and flexible cooling system that improves strip stability by enabling the reduction of the cooling length. By increasing the blowing speed of cooling air, the cooling length can be significantly shorter while the cooling capacity is maintained at the same level.

Fives developed the Aeris® technology at its own test centre by building several scale 1 test benches.  The research works were conducted together with renowned institutes specializing in aerodynamics (Institut Aérotechnique, Saint-Cyr-l'École, France) and fluid flow thermal transfer (Brno University of Technology, Czech Republic). The new technology was tested and optimized in a pilot bench facility before being introduced to the market for hot dip galvanizing lines. 

Aeris®, after-pot cooling technology

Aeris®, after-pot cooling technology advantages:

  • Production capacity increase
  • Additional cooling capacity
  • New coating applications, such as AlZn, GA, GL, aluminized coating, etc.
  • Drastic reduction of after-pot cooling tower height
  • Optimized air and fog cooling length
  • Accurate strip temperature control
  • Energy consumption improvement
     

The Aeris® technology can be applied to wet and dry processes

Dry Aeris®, air cooling for dry processes

Dry Aeris® - air cooling for dry processes uses only one fan for each blowing box with a symmetrical blowing circuit to the strip axis, ensuring equal air velocity on both sides of the strip. 

For special processes: movable air cooling after metallic coating

For galvanealed processes:

  • Movable soaking for GA
  • Fixed soaking for GA
  • Combined soaking or cooling
  • Air cushion unit

For strip cooling - Aeris® high efficiency cooling units:

  • Fine geometry of cooling tubes
  • Self-stabilizing design of fluid dynamics
  • Rear central extraction of air

Wet Aeris® uses a special nozzle design to achieve fog cooling to the desired capacity over a much shorter cooling length, typically one tenth of standard cooling technology. No compressed air is required, making this a highly energy efficient system.

In addition to the water & air knife equipment, a mechanical quick sealing device is installed. This prevents water falling into the pot in case of power outage.
 

The Aeris®, after-pot cooling technology improves strip stabilization, while the footprint is significantly reduced: the Dry Aeris® reduces cooling length by 25% and the Wet Aeris® decreases it by 70%.

⇒ For recruitment-related matters (application, etc.), please do not use this form. Make your requests on this page.

In order to address your request, we need to collect the information listed in the form below

Information on data processing

As a data processor, FIVES implements personal data processing when managing your contact request. The data collected are required for this processing and are retained, unless you object, for a period of 6 months from the last contact between you and FIVES. If the information is incomplete, FIVES will not be able to respond to your contact.

The data collected are exclusively for the use of FIVES departments.

Pursuant to current legislation, you have the right to request access to data concerning you, their correction, deletion and portability, as well as a right of limitation over processing of your data.

These rights can be exercised by email to DPO@fivesgroup.com or by post to the Data Protection Officer at the following address: FIVES, 3 Rue Drouot, 75009 Paris, accompanied by a copy of an identity document.

In case of a dispute involving processing of your personal data, you have the right to make a complaint to the French Data Protection Agency (CNIL).

To find out more about our personal data protection policy click here


*

Despatch of these emails is managed by a FIVES partner located in the United States, an active member of Privacy Shield. The partner guarantees processing compliant with European requirements for personal data protection. Unsubscribe with a single click on a link in the message received.


* required fields

Your message has been sent and will be treated as soon as possible. Thank you for contacting Fives.

Sorry, we encountered a problem, your message was not sent